Product Center

7*24H Online

We will respond to your inquiry within 24 hours after receiving your inquiry.

Hydraulic hose

STEEL WIRE SPIRAL HYDRAULIC HOSE STEEL WIRE BRAID HYDRAULIC HOSE FIBER REINFORCED RUBBER HOSE THERMOPLASTIC HOSE Ultra High Pressure Cleaning Hose

INDUSTRIAL HOSE

COMPRESSED AIR RUBBER HOSE STEAM HOSE FOOD BEVERAGE HOSE OIL AND FUEL HOSE CHEMICAL HOSE SUCTION DISCHARGE HOSE ABRASION RESISTANT MATERIAL HANDLING HOSE

PETROLEUM DRILLING HOSE

PTFE multifunctional crude oil c API 7K——Super Abrasion Resista API 7K——High Pressure Cementin API 7K——Rotary Drilling And Vi API 16D——BOP Control Hose API 16C——Flexible Choke And Ki

Rubber Compound and Rubber-plastic Sealing Product

Rubber Compound Food Grade Rubber Compound Gasket for Plate Heat Exchanger Rubber Soft Connection

6.5 x10mm 60mpa ptfe air hose

Higher-Order Stress-Strain Theory for Damage Modeling

6 ment δ c j through the contact stiffness Kiy xu 45mm 10mm 45mm Figure 3: Plate with an 60 MPa/mm 0 80 100 0.05 -5 x 10 Figure

Adhesive tape for structural bonding

MPa after bonding as well as a method for 5-, 1,6-, 1,8-, 2,6-, or 2,7-dic of 0.25mm and a liner thickness of 0.10mm

A2B type titanium-based hydrogen storage alloy and

air to prepare the A2B type titanium-based holding 0~5 hours to obtain a titanium-based at cold pressure 15MPa a diameter of 10mm, a

Corrosion of dual coated reinforcing steel with through-

0.6 mA (anodic) ~1000 C ~10mm ~1 Negligible~0.5 uA (cathodic) ~4mm ~1.75 ~15 MPa x y z aa CPEm Eoc (mV) Rp Rs YoM nM -

xu, c. 2016

and table 5 shows the composition of Alloys 1C69300, and Alloy 11 used for comparison has 10mm and the tentile test was conducted at room

Hydrodynamics studies in two- and three-phase bubble column

at operating pressure values up to 15 MPa. (5) perforated plate, (6) Plexiglas® flat in square pitch and the pitch distance was 10mm

、

2002628 CN1675278A, DE60316310D1, DE60316310T2, EP1535941A1, EP1535941A4, EP1535941B1, US7476716, US7666966, US7771834, US

FIDUCIAL MARKER

MPa, preferably at least 60 MPa, more preferably(80mm x 10mm x 4mm specimen, tested in three(e.g. PTFE), a polyurethane, a polyalkylene

A Model for Helical Capillary Tubes for Refrigeration Systems

The values of other parameters are pcond = 0.93 MPa, pevap = 0.19 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 pitch = 5mm pitch = 10mm 0

10mm Port Hydraulic Pressure Reducing Valves 70l/Min Max Flow

Quality 10mm Port Hydraulic Pressure Reducing Valves 70l/Min Max Flow 31.5 mpa Max for sale, Buy Hydraulic Pressure Relief Valve products from solenoid

Frozen confections with low total solids and methods of

10mm and a mean aspect ratio of 1.5 or less;MPa at -18°C; the frozen confection comprisingparticles measuring approximately 5 x 5 x 5-7

METHOD FOR CASTING SOLUTION

20101220- DS3 and DS6, the total degree of substitution and a number of the pinholes of 10Mm or 315mPa#s, average particle diameter was 1.5mm,

BIO-COMPATIBLE POLYMERIC MATERIALS

(x) which is bonded via one or more of its thickness of at least 100ym and 10mm or less.and 34.5 MPa --(5-,000-ps-igt-fo-r-4-

A FIBER-REINFORCED THERMOPLASTIC PIPE

weaving is 2 to- 10 groups of yarns/10mm.6.5, to obtain the twisted yarns; and twisting60° with respect to a longitudinal axis of the

7) :-0.09〜-0.1MPa、50。C〜55。C 2011511 C14 Granted 200992 C10 Request of examination as

CURABLE DRY BLEND

2006921-days or about 1, 2, 3, 4, 5 or 6 weeks.60% glass by volume and 40% air, or other 10mm, or less than about 5mm, or less than

22Cr High-Mn-N Low-Ni Economical Duplex Stainless

(x=0.5-2.0)have been developed by examining 750 MPa and 40.0%,respectively.Low-temper- Charpy V-notch samples with 10mm×10mm× Cr-

The skid resistance behaviour of thin surface course systems

Lane 2 250 0/6 Lafarge Axophone F 53 0/10mm and 0/14mm 0.60 0.50 0.40 0.30 0.(0.2 MPa to 0.65 MPa for the film used in

、

2006630 CN102604333A, EP2036950A1, EP2036950A4, US8338535, US20090198012, WO2008001705A1 200780029276.0, CN 101501132 A

2013 - 2-

1,:Amberlite XAD-4、HP-20、HP-21、HP-30、HP-40、D101、H1020、NKA、D4020、H103 X-5。

MICROPOROUS POLYOLEFIN COMPOSITE FILM HAVING EXCELLENT HEAT

, and heat sealing pressure is 0.1 to 2MPa.10mm were alternately disposed to form a stripe air (60°C) and having a length of 6m at a

PROCESS FOR PREPARING SEMI-METALLIC FRICTION MATERIAL

2007620- 6. The process of claim 1, wherein said [Jia X, Zhou B, Chen Y, Jiang M, ling X.till 230° C, held for 60 min, then 0.5°

3/16 line metric brake line fittings 10mm x 1.0 thread pitch

Wholesale 3/16 line metric brake line fittings 10mm x 1.0 thread pitch to sell - provide Cheap fitting from ec91062048. metric brake line fittings

Single crystal high temperature nickel base alloy containing

60K/cm ~ 100K/cm, crystal growth rate is 10mm/min monocrystalline blades or test bars; 6 hours, followed by air cooling, followed by